减压渣油与FCC油浆共炭化的化学组成变化

考察了齐鲁石化胜利炼油厂催化油浆（FCC）和胜利减压渣油（VR）在490℃，0.8MPa下不同混合比的原料和不同反应时间的中间产物的HS、TS、PS、P及其1h中间产物的HS和TS的^1H-NMR。数据结果反映了体系的反应速度。掺入FCC油浆抑制了VR的反应活性，降低了体系的反应速度，增加了基质的溶解度；1h中间产物的组成结构更接近于原料及反应体系的反应性和基质的溶解度；1h中间产物的芳香度越高，取代基越少，侧链越短，基质对VR中的活性反应组分在炭化早期生成的高度缩合物质的溶解度越大。     

纤维混凝土在水工建筑工程中的应用(上)

概述改性混凝土垢发展情况，介绍纤维混凝土在国内外水工建筑物上的应用实例，提出钢纤维增强钢筋混凝土水工建筑结构强度计算方法。包括受弯构件正截面强度，斜截面抗剪强度的计算；重点介绍了网状钢纤维增强混凝土（FOC）在水工建筑物上的应用，包括在渡槽，闸门，小型拦河坝，轻型岸型等工程上的应用实例，T新梁正斜截面的强度计算，板材承载力计算的方法。     

近期河北冶金工业结构调整形势与任务

分析了河北冶金近期行业发展特别关注的几个问题：钢铁生产发展过快；产业结构缺陷，资源供应和环境压力。同时，文章从分析国内外市场形势和国家宏观政策形势入手，提出了河北冶金工业对产品结构调整，工艺装备调整和组织结构调整的必要性，任务和需注意的问题。     

Automatic conversion from lexical words to prosodic words for mandarin text-to-speech system

In real speech, not like lexical words (LWs), prosodic words (PWs) are basic rhythmic units. The naturalness of a Text-to-Speech (TTS) system is directly influenced by the segmentation of the PWs. Most of the PWs are the combination of several LWs. In this paper, three Lexical Combination Models are proposed to combine LWs into PWs, including a Directed Acyclic Graph Model, a Segmentation Model and a Markov Model (MM). To cope with the situation where some long LWs should be segmented into two or more PWs, a Lexical Split Model (LSM) is applied to the long LWs. Experimental results prove that relatively constant results with various training data can be obtained from a MM. The Transformation-Based Error Driven Learning (TBED) algorithm, for its high performance of individual property, is applied in combination with the MM to improve the precision of PW segmentation. Experiments show that among the three proposed models, the MM combined with TBED and LSM, leads to the best performance, in which a precision of 93.00% and a recall of 93.23% are achieved. The perception test indicates that by using PWs as the lowest prosodic units a speech sounds more natural and acceptable than by using LWs. This paper is supported by NSFC Project (60503071); 973 Natural Basic Research Program of China (2004CB318102); Postdoctor Science Foundation of P. R. China (20070420275).     

兰州重离子加速器大型真空室

已建成的兰州重离子加速器的真空室是一个大型整体结构的超高真空容器,直径约10m,高4.5m,重65000kg,内表面积211m~2,容积100m~3,工作真空度为5×10~(-5)Pa。采用有限单元法在计算机上用SAP-5C程序对真空室受力分析进行了计算。真空室结构材料选用瑞典Uddeholm钢厂生产的316 L 超低碳不锈钢。承制此大型容器的是航天工业部风华机器厂。由于结构庞大,首先将真空室分成八大块和几小块在工厂制造,然后运至现场焊制成一整体容器并进行机械加工。所有密封焊缝均用着色渗透液,X-射线探伤和氦质谱探漏仪进行检查和探漏。     

聚合物-金属界面相形貌的研究

环氧树脂在 Al 合金表面生成纤维状的界面相结构,其形成、发展和特征与树脂的体系、交联反应条件以及 Al 合金的表面状态有关。环氧树脂的基础相为颗粒状的超结构组织。聚合物界面相的力学破坏表现为纤维体的拉伸、变形和断裂,而基础相在纯剪切受力时出现在45°方向的裂纹,并发展导致连接层的破坏。     

Formation of layered structure on bismuth-borate glass surface

X-ray diffraction analysis shows that the transformation during heat treatment from amorphous to crystalline phases of bismuth-borate glass samples takes place in sequences. After a short heat treatment, 5 min at 550 °C, a layered structure with a preferred orientation of crystallites on the surface is observed. After a long heat treatment, 8 h at the same temperature, normal polycrystalline bulk samples are obtained.     

Effects of hot-carrier stress on high performance polycrystalline silicon thin film transistor with a single perpendicular grain boundary

This paper is a report on the effect of a single perpendicular grain boundary on the hot-carrier and high current stability in high performance polycrystalline silicon (poly-Si) thin film transistors (TFTs). Under a hot carrier stress condition (Vg = Vth + 1 V, Vd = 12 V), the poly-Si TFT with a single grain boundary is superior to the poly-Si without any grain boundary because of the smaller free carriers available for electric conduction. The shift of transconductance in poly-Si TFT with a single grain boundary is less than 5% after hot carrier stress during a period of 1000 s. The shift of transconductance is about 25% in the case of the poly-Si TFTs without a grain boundary in the channel. On high current stress, the poly-Si TFT without the grain boundary is less degraded than the poly-Si TFT with the grain boundary because the concentrated electric field near the drain junction is lower.     

A new iterative order reduction (IOR) method for eigensolutions of large structures

Order reduction is a computationally efficient method to estimate some lowest eigenvalues and the corresponding eigenvectors of large structural systems by reducing the order of the original model to a smaller one. But its accuracy is limited to a small range of frequencies that depends on the selection of the retained degrees of freedom. This paper proposes a new iterative order reduction (IOR) technique to obtain accurately the eigensolutions of large structural systems. The technique retains all the inertia terms associated with the removed degrees of freedom. This hence leads to the reduced mass matrix being in an iterated form and the reduced stiffness matrix constant. From these mass and stiffness matrices, the eigensolutions of the reduced system can be obtained iteratively. On convergence the reduced system reproduces the eigensolutions of the original structure. A proof of the convergence property is also presented. Applications of the method to a practical GARTEUR structure as well as a plate have demonstrated that the proposed method is comparable to the commonly used Subspace Iteration method in terms of numerical accuracy. Moreover, it has been found that the proposed method is computationally more efficient than the Subspace Iteration method. Copyright © 2003 John Wiley & Sons, Ltd.     

真空制盐蒸发结晶器的设计与实践

真空蒸发制盐外热式强制逆循环轴向出料蒸发结晶器，经多个厂家生产应用实践证明是成功的，具有生命力的。这种新型结构，作为一项新技术新设备应加强研究，总结提高，推广应用。不断完善。文章从流体力学、结晶机理角度要求，到具体工程设计参数和材质选用。论述了该罐的特点。